how to mix HCG

Have you recently received your hCG kit and are unsure about how to mix HCG injection? At The HCG Institute, we will walk you through the steps to ensure you are ready to go. Continue reading to discover the process of how to mix hcg injection powder.

Injectable HCG usually arrives in powder form (lyophilized) and must be mixed before administration. Lyophilization improves the storage life of hCG, ensuring that you get your product with its maximum potency. 1 The solution used to mix lyophilized HCG is bacteriostatic water which is usually provided with your purchase. Bacteriostatic water contains 0.9% Benzyl Alcohol to prevent microbial growth.

Step 1: Wash your hands and gather your materials.

First, thoroughly wash your hands with soap and water and dry well, or use an alcohol-based hand-cleaning product before mixing your hCG injection powder. Gather your materials.

These supplies will come with the hCG injection kit when you buy from The HCG Institute online.

Step 2: Prepare your materials.

hcg mixing

Step 3: Draw up your bacteriostatic water.

2. To draw bacteriostatic water from the vial, pull back on the plunger and pull air into the syringe equal to the amount of liquid you will need to draw. Pull the needle cover straight off the needle and insert the needle straight through the rubber stopper. Push the plunger of the syringe down and inject air into the vial. The bacteriostatic water vials are under vacuum with negative oxygen pressure, rendering it harder to tug the fluid out. Thus, injecting air helps alleviate the vacuum-like pressure pulling against you.

3. Hold the bacteriostatic water vial upside down and withdraw the amount of bacteriostatic water needed to dilute the hCG powder.

4. Clear the air bubbles out of the syringe by tapping it with your finger to get all of the air bubbles to the top. Push up on the plunger slightly until they are all gone.

Step 4: Inject bacteriostatic water into lyophilized HCG.

how to mix hcg

  1. When measuring the amount of water, read from the top ring (closest to the needle) and not the bottom ring or the raised section in the middle of the plunger. Make sure the top ring of the rubber seal is at the correct mark. If you are unable to get the correct amount of water transferred, please contact us so that we can adjust your dose to allow for the different concentration.
  2. Insert the diluent into your vial of powdered hCG. Swirl gently until the hCG powder is completely dissolved. Don’t shake or aggressively mix it. Once you are finished, you should no longer see any powder in the HCG vial.

Step 5: Draw your hCG medication.

hcg mixing syringe

  1. Get your insulin syringe and with the needle cover still on the needle, pull back on the plunger and pull air into
  2. Turn the vial upside down, slowly pull back on the plunger, and let the hCG hormone enter the syringe, filling up to the 25 syringe marks.
  3. Gently tap the syringe until the air bubbles rise to the top of the syringe barrel. Then push the plunger, forcing the air out of the syringe. Once again pull the plunger back to the prescribed dosage. Repeat these steps if needed.
  4. Prefill all your daily syringes and store them inside the refrigerator. Prior to mixing, powdered HCG can be kept at room temperature. But once you add the bacteriostatic water, it should be kept in the fridge.

Step 6: Inject your HCG.

  1. Clean the injection site with an alcohol prep pad before administering the hCG injection. Check this link on how to administer hCG injections subcutaneously.2

Step 7: Discard used syringes properly.

  1. Immediately discard all used syringes in a sharps disposal container to reduce the risk of needle sticks, cuts, or punctures from loose sharps. If you don’t have or did not purchase this together with your medication, you can use a heavy-duty plastic household container as an alternative (an empty liquid laundry detergent container is a good example) that is able to close, with a tight-fitting, puncture-resistant lid, without sharps being able to come out. 3

How to mix hcg injections is a precise process that requires careful attention to detail to ensure safety and efficacy. By following the recommended steps provided by The HCG Institute, you can prepare a properly reconstituted solution for administration. Remember to use bacteriostatic water for reconstitution, calculate the correct dosage, and store the mixed solution appropriately to maintain stability. Adhering to these guidelines will help minimize the risk of contamination, ensure accurate dosing, and optimize therapeutic outcomes.

If you have any questions or concerns about how to mix injection powder, do not hesitate to contact us for guidance and support. With proper preparation and administration, you can safely harness the benefits of HCG therapy for your health and wellness goals.

Frequently Asked Questions

What is the correct ratio for mixing HCG

The correct ratio for mixing HCG depends on the concentration of the HCG powder and the volume of bacteriostatic water used for reconstitution. It is crucial to follow the specific instructions provided by your healthcare provider or the manufacturer of the HCG product you are using. These instructions will ensure the accurate reconstitution of the HCG solution for safe and effective use.

Can I use tap water to mix HCG injections?

No, it is not recommended to use tap water to mix HCG injections. Tap water may contain impurities or bacteria that could compromise the sterility of the HCG solution and increase the risk of contamination or infection. It's essential to use bacteriostatic water, which is specifically designed for reconstituting medications like HCG. Bacteriostatic water contains an antimicrobial agent (usually benzyl alcohol) that helps prevent the growth of bacteria, ensuring the safety and integrity of the HCG solution for injection. Always follow the instructions provided by your healthcare provider or the manufacturer of the HCG product to ensure proper reconstitution and administration.

Do I need to refrigerate HCG after mixing?

Yes, it's generally recommended to refrigerate HCG after mixing to maintain its potency and stability. Reconstituted HCG solution is sensitive to light, heat, and air, which can degrade its effectiveness over time. Refrigeration helps slow down the degradation process and preserve the potency of the HCG solution. However, it's essential to follow the specific storage instructions provided by your healthcare provider or the manufacturer of the HCG product you're using. Some formulations may have different storage requirements, so always consult the product label or your healthcare provider for guidance on proper storage and handling of reconstituted HCG.

Can i still use mixed hCG injection that's left outside?

Once mixed, hCG injections should be used promptly or refrigerated to maintain stability and sterility. Leaving a mixed hCG injection outside the refrigerator for an extended period can compromise its potency and increase the risk of contamination. Exposure to light, heat, and air can degrade the solution, reducing its effectiveness. Using a mixed hCG injection that has been left outside for an extended period is not recommended, as it may not provide the intended therapeutic effects and could potentially lead to adverse reactions or infections. It's essential to follow the specific storage instructions provided by your healthcare provider or the manufacturer of the hCG product to ensure safety and efficacy. If you have any doubts about the integrity of a mixed hCG injection, it's best to discard it and prepare a new dose as directed.